A complete Datsun 240z choke mechanism that has been professionally cadmium plated with a brand new choke knob and grommet. The complete mechanism has been lubricated and will operate like...
Brand new from Nissan. Sold in sets of 2
Center linkage that installs between the carburetors OUT OF STOCK
Pictured are Brand New 1970 or 1971 Datsun 240z choke clamps that install at the top of SU Carburetors in order to keep the choke cables attached to the carburetors....
Datsun 240Z heat shield from 1970-1971. Completely restored and will work on 73-74 intake manifolds if using early SU carburetors from 70-71. On exchange only
Brand new 1970 inspection door retainer clips to keep the doors in place for the Early Datsun 240z up until May 1970. Sold in set of 2
Brand New. Does not include Knob.
Completely restored transmission cross member mount for the 1970 or early 1971 Datsun 240z
Oil cap from a 1970 240z with oil embossed on the top
Center linkage for the SU carburetors from early 1970 to early 1971 year.
Complete 1972 or 73 Datsun 240z choke mechanism with brand new choke knob and grommet.
A must to complete the restoration of your 1972 or 1973 240z car. This decal installs on the underside of your hood on the passenger side.Please specify which year your...
A must to complete your 240z restoration. This Inertia Wheel Weight Decal installs on the underside of the hood just below the emissions control decal on the passenger side. This...
SU carburetor center linkage for late 1971 and 1972 240z.
Brand new from Nissan. Will fit both '72-'73 brake systems.
Brand new from Nissan 2 per Set
Brand New brake booster decal for 1973 Datsun 240z Just peel and apply to the top of the brake booster
Brand New emissions control decal for 1973 Datsun 240z that applies to the underside of the hood on the passenger side
Brand New inertia wheel weight decal that applies to the underside of the hood on the passenger side
Completely restored to factory condition and comes with bolt on hardware
** On exchange only Bolt-on hardware included
1964 - 1968 Datsun Fairlady Roadster Hood Latch Assembly Parts have been professionally stripped and plated to factory specifications OUT OF STOCK
Brand new Nissan intake plugs to complete your intake manifold. Sold in sets of 3
Water pump pulley that has been restored to factory. Will fit all years of the 510 models NOT PLATED AT THIS TIME BUT AVAILABLE
Brand new fuel filter and retainer bracket from Nissan that bolts on to your interior passenger fender. Comes with brand new bolt on hardware
Brand New from Nissan. This part installs on top of your thermostat housing to holder your distributor wires in place that go over the valve cover on the engine.
Brand New Datsun front fender washers that install next to the hood. These washers are the correct ones that are flush to the top of the fender next to the...
New Nissan wire hoses clamps that attach to the fuel pump and fuel rail in engine bay . Price per set of 10.
Brand New from Nissan is a breather that is essential when restoring your stock transmission . Will work for all 4 speed Transmissions
240z Air Cleaner Bolt on hardware to install your air cleaner housing to front of the S U carburetors .
air cleaner box has been restored to factory condition
New reproduction gaskets that install on the back side of your stock air cleaner housing. 2 per set
Non emissions Air cleaner housing that has been restored to factory condition. This air cleaner housing came on all early Datsun 240z cars A part that very Hard to...
Anti back fire valve that is used on the intake manifold. OUT OF STOCK
1970 to 1972 Datsun 240z balance tube . Hardware for balance tube is also available.
Brand new from Nissan intake balance tube bolts to install it on the top of your intake manifold. Sold in set of 4 on Exchange only
Brand new balance tube gaskets that provides a air tight seal for intake manifold and make your carburetors work properly. Sold in set of 2
Brand new balance tube plugs from Nissan to prevent gas fumes from escaping from your intake system. Sold in a set of 3 to complete one system
Brand new battery firewall insulator to bolt your battery retainer to the firewall.
Brand new PCV hose for your 240z car. These hose runs between the engine block to your PCV valve on your balance tube.
Brand New Datsun 240z Brake Booster decal that installs on top, right next to the firewall. It is a very highly visible in your engine bay. This decal installs in...
Pictured is a complete New set of brake and fuel line retainer brackets. Comes with brand new bolt on hardware to install. .
Brand new wiring loom that keeps the wiring around your distributor from getting damaged by the fan at front of your engine.
28 per set. Comes with brand new lock & flat washers.
Brand from Nissan is a engine head pipe that installs on the back side on the passenger side on either the E31 or E88 head.